How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
How do you feel in regards to Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the job can move immediately; if you have to open up a wall to eliminate the old tub as well as position the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually certified yourself for the work and fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently bought a new bathtub and also don't require to transform the arrangement of your previous water system pipelines.
Your tools and product list should make up the following:
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub till the level reviews level.
To set up faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks and tighten them if needed. Load the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub needs to wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in place in between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our excerpt on A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to read our short article. Appreciated our write up? Please share it. Help other people discover it. Thanks a bunch for your time. Please stop by our site back soon.
Find Out More Report this page